Elevate RubberCover Contact Bonding Adhesive Aerosol Spray - 750ml
Couldn't load pickup availability
Delivery:
IN STOCK. Next Day Delivery (if ordered before 14:00)
Key Features:
- Material : Contact Adhesive Spray BA-2016 for EPDM
- Size: 750ml
- Application: Bonds Firestone EPDM contact adhesive designed for bonding EPDM to wood, metal, masonry and other acceptable substrates
- Coverage: General rate (for 2 sides) can be achieved: 750 ml spray aerosol can: between 1.2 and 1.5 m² and per 22 l pressurized canister: maximum 70 m²
Description:
The ElevateTM Bonding Adhesive BA-2016-S/TF is a sprayable solvent-based contact adhesive specifically designed for bonding Elevate RubberCover™ EPDM membranes to approved insulations in addition to wood, metal, masonry and other acceptable substrates.
Application:
Surfaces that will receive Bonding Adhesive BA loose and foreign materials, oil, grease and other cleaned with a brush or clean rag.
Gently spray the BA-2016 S/TF onto both surfaces to be adhered. Apply the adhesive onto the EPDM membrane last. The ideal distance between the surface and the spray gun is 20 - 30 cm. Try to apply the correct amount of adhesive in a single layer and avoid areas of accumulation. Care must be taken not to apply BA-2016 S/TF over seaming areas. Application temperatures may vary between 5°C and 25°C. At temperatures below 5°C, the adhesive may become too thick, and consequently, an insufficient quantity of adhesive may be sprayed on the surface. At temperatures above 25°C, and especially with the membrane exposed to the sun,the adhesive may skin over and drying times will be extended.
Also at high temperatures, protect the canister and hose from direct sunlight. If the canister heats up, it may affect the spraying pattern. Allow the adhesive to flash off completely before mating the surfaces. Test the adhesive for its dryness using the touch-push test procedure. Mate the membrane to the substrate and apply sufficient pressure with a broom.
Downloads & Data Sheets:
Product Data Sheet
Related Products
Elevate RubberCover Roof EPDM (1.14mm thick) - CUT TO SIZE
Elevate RubberCover Roof EPDM (1.52mm thick) - CUT TO SIZE
Elevate RubberCover Contact Bonding Adhesive (BA 2012)
Elevate RubberCover Contact Bonding Adhesive Aerosol Spray - 750ml
Elevate RubberCover 3" Splice Tape - per linear mtr
Elevate RubberCover 5" QuickSeam™ Flashing - per linear mtr
Elevate RubberCover 6" QuickSeam™ Cover Strip - per linear mtr
Elevate RubberCover 9" QuickSeam™ FormFlash - per linear mtr
Elevate RubberCover 12" QuickSeam™ FormFlash - per linear mtr
Elevate RubberCover 18" QuickSeam™ FormFlash - per linear mtr
Elevate RubberCover Spray Contact Bonding Adhesive Cannister - 17Ltr
Plastisol Metal Wall Trim for EPDM - 3m x 70mm x 30mm
Permaroof Plus Roof Edge Trim - 100mm x 2.5m (Including Foam & Fixing Pins)
Firestone® RubberCover 8" Circular Corner Flashing Piece
Firestone® RubberCover Moulded Pipe Flashing 25mm - 175mm
Permaroof 100 Polyurethane Liquid Waterproofing Roof Kit - 5m2
Permaroof 100 Polyurethane Liquid Waterproofing Roof Kit - 10m2
Delivery:
IN STOCK. Next Day Delivery (if ordered before 14:00)
Key Features:
- Material : Contact Adhesive Spray BA-2016 for EPDM
- Size: 750ml
- Application: Bonds Firestone EPDM contact adhesive designed for bonding EPDM to wood, metal, masonry and other acceptable substrates
- Coverage: General rate (for 2 sides) can be achieved: 750 ml spray aerosol can: between 1.2 and 1.5 m² and per 22 l pressurized canister: maximum 70 m²
Description:
The ElevateTM Bonding Adhesive BA-2016-S/TF is a sprayable solvent-based contact adhesive specifically designed for bonding Elevate RubberCover™ EPDM membranes to approved insulations in addition to wood, metal, masonry and other acceptable substrates.
Application:
Surfaces that will receive Bonding Adhesive BA loose and foreign materials, oil, grease and other cleaned with a brush or clean rag.
Gently spray the BA-2016 S/TF onto both surfaces to be adhered. Apply the adhesive onto the EPDM membrane last. The ideal distance between the surface and the spray gun is 20 - 30 cm. Try to apply the correct amount of adhesive in a single layer and avoid areas of accumulation. Care must be taken not to apply BA-2016 S/TF over seaming areas. Application temperatures may vary between 5°C and 25°C. At temperatures below 5°C, the adhesive may become too thick, and consequently, an insufficient quantity of adhesive may be sprayed on the surface. At temperatures above 25°C, and especially with the membrane exposed to the sun,the adhesive may skin over and drying times will be extended.
Also at high temperatures, protect the canister and hose from direct sunlight. If the canister heats up, it may affect the spraying pattern. Allow the adhesive to flash off completely before mating the surfaces. Test the adhesive for its dryness using the touch-push test procedure. Mate the membrane to the substrate and apply sufficient pressure with a broom.
Downloads & Data Sheets:
- Choosing a selection results in a full page refresh.